Blog

Electro-Spinning Unit In Nepal

Electro-Spinning Unit In Nepal

Spinning innovation into fibers is an art of science and engineering. The spinning process starts when the solution is pumped at a constant flow rate and a specific voltage is applied to create an electric field between the needle tip and the collector. A charge accumulates at the liquid surface. When the electrostatic repulsion is higher than the surface tension the liquid meniscus is deformed into a conically shaped structure known as the Taylor cone.

Once the Taylor cone is formed, the charged liquid jet is ejected towards the collector. Collectors can be but are not limited to, stationary flat plates, rotating drums, mandrels, and disks. Depending on the solution viscosity solid fibers will be formed as the solvent evaporates from the whipping motion that occurs during its flight time from the Taylor cone to the collector. The result is a non-woven fiber mat that is deposited on the collector.

Introduction to the Electrospinning Process

Electrospinning is a manufacturing technique involving electrostatic driven process used to create electrospun fibers. The diameter of these fibers typically ranges between tens of nanometers to a few micrometers. One of the main advantages of the electrospinning technique is its versatility of processing to create fibers with multiple arrangements and morphological structures. The popularity of the electrospinning technique has allowed multiple technologies such as tissue engineering, regenerative medicine, and encapsulation of bioactive molecules, to emerge and evolve over the past decade.

These days the electrospinning technique is not just for academic research, but one with real commercial applications. Currently, multiple industries around the world have adopted this technique in the development of new product innovations. Some of the applications where electrospinning is being currently used are tissue engineering (NanoAlignedTM, NanoECMTM, NanoCareTM, NanoMeshTM, Absorv®, TegadermTM), drug delivery (Rivelin® Patch), food encapsulation, insulating materials, energy conversion and storage, air and water filtration, among others.

Electrospinning Nanofibers: Needle-less versus Needle-based

There are two ways nanofibers can be made through the electrospinning technique: needle-less and needle-based. Prior to selecting which method it is important to consider the advantages and disadvantages of both.

In needle-less electrospinning, the starting polymer solution is transferred to an open vessel where the fibers are generated from a stationary or rotating platform. Mass production of material is one benefit in the needle-less electrospinning process but there are many disadvantages. Fiber morphology and quality are not precisely controlled, the raw materials that can be utilized are limited, which in turn limits versatile fiber production and process parameters such as flow rate, cannot be controlled.

In needle-based electrospinning, the starting polymer solution is typically contained in an air-tight closed reservoir, this minimizes and prevents solvent evaporation. This important difference allows for a wide variety of materials, including high volatile solvents, to be easily processed. There are many advantages of needle-based electrospinning, including flexibility to process different structures like core-shell and multi-axial fibers. This distinction allows for active pharmaceutical ingredients (API) to be incorporated within a fiber. Additional advantages of needle-based electrospinning is tightly controlled flow rate, number of jets and minimizing solution waste. These advantages of needle-based electrospinning have increased the popularity of this technique, resulting in a high number of published work on electrospun fibers that offer a wide variability of solution recipes.

ItemsSpecification
ModelSuper ES-2
Spinning arrangementVertical, Horizontal, Inert Gas Spinning, Under solvent spinning
Input voltage90-240 VAC+/-
H.V. Power supplyVoltage output Range : 0-50 KV and 0-60 KV Output Current : 0-400 uA and 0-1 mA Dual Digital Panel Meter for Voltage and Current Voltage Regulation : Variable as desired Constant voltage and constant current mode Built-in arc protection circuit Overload trip protection available
Syringe Pump Single channel and Dual channel with independent controlFlow rate : 0.1 ml/hr to 1000 ml/hr Programming : Multistage programming Control : Volume, Time, Spray time Flow and Diameter Acceptable Syringe size : 1 ml to 60 ml Control : Microprocessor control
SpinneretCo-axial nozzle for making core-shell, hollow and Bi-component fiber Multi-nozzle for high throughput Single Nozzle Tri-Axial spinneret
Flow rate0.1μl/min – 3ml/min
CollectorDrum Collector : Diameter : 50 mm Length: 200 mm Drum Collector : Diameter : 100 mm Length : 200 mm Drum Collector : Diameter : 2 mm Length : 200 mm Drum Collector : Diameter : 5 mm Length : 200 mm Disc Collector : Diameter : 100 mm Width : 10 mm Plate Collector : 200 mm X 200 mm
Spinning Chamber/Fume HoodExhaust Fan with good ventilation arrangement Inert gas purging facility Static removal device-residual charge discharge stick HV power supply will shut down when door is opened UV Light Arrangement White light arrangement Glass door
Collector RPM200 – 5500 RPM
Single NozzleVariable nozzle size
Multi Nozzle4 Nozzle with variable nozzle size
Core Shell nozzleVariable nozzle size
HumidityDisplay (Control Optional)
Chamber Temp.atm – 70°C
Syringe Temp.atm – 200°C
VentilationInbuilt exhaust fan
Power light20 watt Two LED lights
U.V. light1 U.V. light
Emergency stopInbuilt emergency stop button
Main switchInbuilt On / Off button
AccessoriesNeedles with blunt end and lure lock compatibility Syringes with Glass/PP/Teflon body and lure lock Syringe heater up to 150 oC Standard spinning samples (50 ml) Branded laptop will be provided along with machine UPS and Computer
Foot print840 X740 X 1700 mm
Construction materialAluminium, Glass, Aluminium composite sheet, Granite sheet, Plastic

Leave a comment